HomeYour location:HomeHigh voltage electrical appliancesHigh-voltage arresterValve type lightning arrester → FZ series valve type lightning arrester
Column tabs 
Product name: FZ series valve type lightning arrester
specification: FZ series valve type lightning arrester
  Zoom Zoom in on the image
Category: High voltage electrical appliances -- Valve type lightning arrester
Column tabs 
Price: factory price
Brand: Shanghai
Place of Origin: China
Column tabs 
Available Quantity: batch
delivery cycle: Spot goods (or inquire by telephone)
tabs
  Shanghai Beiyuan Industry and Trade Co.,Ltd
+86-21-66770508
+86-13916500500

Email 91way@163.com
Wechat 13916500500(Wechat)


FZ series valve type lightning arresterDetailed product description:Column tabs
Application of FZ series valve type lightning arrester:

The FZ series 3-110kV valve type lightning arrester is a protective electrical device used to protect the insulation of AC substation equipment from atmospheric overvoltage damage.
This applies to:
1. Indoor and outdoor: The ambient temperature of the usage location is -40 ℃ to+40 ℃;
2. The altitude of the usage location shall not exceed 1000m;
3. The maximum relative frequency voltage that may occur at the installation site should not exceed the rated voltage of the lightning arrester.
It is not suitable for places with severe pollution and violent vibrations.  
Structure and performance:
The FZ series lightning arrester consists of three parts: top cover, basic components, and insulation base. In addition to the above three parts, the 110kV lightning arrester is also equipped with a voltage equalization ring. The basic components are sealed and equipped with spark gaps, valve plates, and pressure equalization resistors. A 35~110kV lightning arrester is composed of three standard basic components with voltages of 15, 20, and 30kV, as well as two other non-standard basic components with voltages of 15 and 30kV. The FZ series lightning arrester has two types of bases, and products with different voltage levels require bases of different heights.
1. The lightning arrester is connected between the high-voltage wire and the ground. When atmospheric overvoltage occurs on the wire that poses a threat to the substation equipment, the spark gap will activate. Due to the action of the spark gap and valve plate, the amplitude of the overvoltage on the protected equipment is limited, the insulation of the equipment is protected, and the power frequency continuous current is cut off within 0.01 seconds, restoring the system to its political working state.
(1) Conductance current measurement: Apply a direct current voltage (with a fluctuation of no more than ± 1.5%) specified in the characteristic table to both ends of the basic component, and the conductivity current flowing through the basic component should comply with the specifications in the characteristic table.
(2) Insulation resistance test: Use a 2.5kV megohmmeter to measure the insulation resistance of basic components, and the resistance value is not specified. But the results of each experiment should be similar.
2. During transportation and storage, it should be placed upright.
3. During operation, the original paint layer of the lightning arrester should be repainted every 1-2 years.
4. During installation, the horizontal tension of the top lead of lightning arresters with a voltage range of 3-60kV should not exceed 294N (30kgf), and for 110kV lightning arresters, it should not exceed 196N (20kgf).
5. FZ-110 lightning arrester is used to protect 110kV AC transformer equipment with neutral point not grounded or grounded through arc suppression coil from damage caused by atmospheric overvoltage. A basic section of 15kV non-standard components (with different characteristics from 15kV standard components) is installed at the top, while the remaining four sections are composed of 30kV non-standard components (with different characteristics from 30kV standard components).

Model or series
Base height H (mm)
FZ series 3-60kV
one hundred and sixty-seven
FZ-110 type
two hundred and thirty-one

Installation dimensions of FZ series valve type lightning arrester
Outline drawing of FZ series valve type lightning arrester

model
FZ-3
FZ-6
FZ-10
FZ-15
FZ-20
FZ-30
FZ-36
FZ3-35
FZ-40
FZ-60
FZ-110J
FZ-110
total height
H(mm)
five hundred and fifteen
five hundred and sixty
six hundred and ninety
eight hundred and sixty
nine hundred and eighty
one thousand and twenty
one thousand and five hundred
one thousand three hundred and three
one thousand seven hundred and forty
two thousand three hundred and eighty
three thousand four hundred and eighty
four thousand one hundred and twenty
weight
(kg)
forty-five point eight seven
forty-eight point eight four
fifty-five point three zero
sixty-four point six nine
seventy point five one
seventy-two point two zero
one hundred and twelve point zero seven
ninety-two point five zero
one hundred and twenty-three point eight nine
one hundred and seventy-one point two seven
two hundred and fifty-seven point eight zero
three hundred and six point five two


FZ series valve type lightning arrester

FZ series valve type lightning arrester
Product Category
All product information on this website is translated by Baidu machine translation, which may not be completely accurate and is only for reference