361R Angular stroke electronic electric actuatorDetailed product description：

Overview of 361R Angular Travel Electronic Electric Executive Mechanism



Specification and model of 361R angular stroke electronic electric actuator

Product Features
1. The actuator is designed with a servo system (without the need for a separate servo amplifier), which only requires the connection of a DC4-20mA (or DC1-5V) signal and an AC220V single-phase power supply to operate. Equipped with internal wiring terminals, the wiring is extremely simple and convenient.  
2. The key component of the actuator - the controller, adopts the most advanced hybrid integrated circuit, sealed and cast with resin, has a box shaped appearance, small volume, and high reliability.
3. The feedback detection of the driving quantity adopts high-performance conductive plastic potentiometers with a resolution of less than 0.4%.
4. Equipped with self diagnostic function, when a fault occurs, the indicator light on the controller will immediately send out an indication signal.
5. The state selection switch can be used to set the cut-off signal when the valve core is in the fully open, fully closed, or self-locking state.
6. The state selection switch can be used to set (forward and reverse actions).
7. The state selection switch can be used to set the input signal to (DC4-20mA or DC1-5V).
Adjusting the work zero point (starting point) and travel (ending point) is simple and easy.
When there is a sudden power outage, it can ensure that the valve core is self-locking.  
10. Adopting synchronous belt transmission effectively reduces noise.
11. Delay protection function, capable of implementing state self-locking at rated load, can immediately activate protection when a fault occurs, and can reverse operation to cancel delay protection

Main technical parameters of 361R angular stroke electronic electric actuator

power supply voltage	AC220 ± 10%, 50Hz.
Power consumption (at rated load)	Specification A actuator 50VA;
	Specification B-type actuator 150VA;
	Specification C-type actuator 220VA
input signal	DC4-20mA or DC1-5V
output signal	DC4-20mA (load resistance below 500 Ω) or DC1-5V
control accuracy	Basic error: ± 1%; Return difference ≤ 1%; Dead zone ≤ 1%
Scope of work schedule adjustment	Zero point ± 25%; 20% to 100% of the itinerary
Protection rating	IP55
Explosion proof level	Exd II BT4
overload protection	Specification A and B type actuators are optional, and specification C series actuators must be equipped

External wiring
The input and output signals should use shielded cables. The power line shall not share the same cable with the signal line

Model number	Ordinary (S-type) actuator	Explosion proof (X-type) actuator
power cable	3-core S=1.5mm2	3-core S=1.5mm2 outer diameter φ 9 ± 1
signal cable	4-core S=1.5mm2	4-core S=1.5mm2 outer diameter φ 11 ± 1
Cable entry port	2-PF(G1/2)	Can install protective sleeve PF3/4 (G3/4)

environmental conditions

environmental conditions	Ordinary (S-type) actuator	Explosion proof (X-type) actuator
Ambient temperature	No space heater -10 ℃~60 ℃	-10℃～40℃
	Space heater -35 ℃~60 ℃
relative humidity	Below 95%	45%～85%
Environmental gas	Non corrosive gas
mechanical vibration	Below 1.5g

Main technical parameters

Model	Output torque Nm	Action time (S/90o)	Maximum rotation angle
361RSA-02	twenty	eight point five	0-90°
361RSA-05	fifty	seventeen
361RSB-10	one hundred	eighteen
361RXB-10
361RSB-20	two hundred	thirty-six
361RXB-20
361RSC-30	three hundred	twenty-four
361RXC-30
361RSC-50	five hundred	forty-two
361RXC-50
361RSC-60	six hundred	forty-eight
361RXC-60
361RSD-100	one thousand	thirty
361RSD-150	one thousand and five hundred	thirty-eight
361RSD-200	two thousand	forty-six