LDE Stainless steel electromagnetic flowmeterDetailed product description：

LDE intelligent electromagnetic flowmeter is an induction instrument that measures the volume flow rate of conductive medium inside a tube based on Faraday's law of electromagnetic induction. It adopts embedded technology of single-chip microcomputer to achieve digital excitation, and adopts CAN fieldbus on the electromagnetic flowmeter, which is the first of its kind in China and the technology has reached the leading level in China.
The LDE electromagnetic flowmeter can not only meet on-site display requirements, but also output 4-20mA current signals for recording, regulation, and control. It has been widely used in industrial technology and management departments such as chemical, environmental protection, metallurgy, medicine, papermaking, and water supply and drainage.
In addition to measuring the flow rate of general conductive liquids, LDE electromagnetic flowmeters can also measure the volumetric flow rate of liquid-solid two-phase flow, high viscosity liquid flow, and salt, strong acid, and strong alkali liquids.

Performance characteristics:
The instrument structure is simple, reliable, without moving parts, and has a long working life.
No flow blocking components, no pressure loss or fluid blockage.
No mechanical inertia, fast response, good stability, can be applied to automatic detection, adjustment, and program control systems.
The measurement accuracy is not affected by the type of measured medium and its physical parameters such as temperature, viscosity, density, pressure, etc.
Different combinations of PTFE or rubber lining materials and electrode materials such as Hc, Hb, 316L, Ti can adapt to the needs of different media.
There are various flow meter models available, including pipeline type and plug-in type.
Using EEPROM memory, the storage of measurement and operation data ensures safety and reliability.
It has two types: integrated and separated.
High definition LCD backlit display.

Technical parameters
Instrument accuracy: pipeline type 0.5 level, 1.0 level; Insertion type 2.5 level
Measurement medium: various liquid and liquid-solid two-phase fluids with conductivity greater than 5 μ S/cm.
Flow velocity range: 0.2-8m/s
Work pressure: 1.6MPa
Environmental temperature: -40 ℃ to+50 ℃
Medium temperature: PTFE lining ≤ 180 ℃
Rubber material lining ≤ 65 ℃
Explosion proof mark: Exmibd Ⅱ BT4
Explosion proof certificate number: GYB01349
External magnetic interference: ≤ 400A/m
Shell protection: integrated type: IP65;
Detached type: Sensor IP68 (5 meters underwater, limited to rubber lining)
Converter IP65
Output signal: 4-20mA.DC, load resistance 0-750 Ω
Communication output: RS485 or CAN bus
Electrical connection: M20 × 1.5 internal thread, φ 10 cable hole
Power supply voltage: 90-220V.AC, 24 ± 10% V.DC
Maximum power consumption: ≤ 10VA

Instrument selection
Range confirmation
The flow rate of the medium measured by the general industrial electromagnetic flowmeter should be 2-4m/s. In special circumstances, the minimum flow rate should not be less than 0.2m/s and the maximum should not be greater than 8m/s. If the medium contains solid particles, the commonly used flow rate should be less than 3m/s to prevent excessive friction between the lining and the electrode; For viscous fluids, the flow velocity can be chosen to be greater than 2m/s. A higher flow velocity helps to automatically eliminate the effect of viscous substances attached to the electrode, which is beneficial for improving measurement accuracy.
Under the condition that the range Q has been determined, the size of the flowmeter diameter D can be determined based on the range of flow velocity V mentioned above, and its value can be calculated by the following formula:
Q=πD2V/4
Q: Flow rate (㎡/h) D: Inner diameter of pipeline V: Flow rate (m/h)
The range Q of the electromagnetic flowmeter should be greater than the expected maximum flow value, while the normal flow value should be slightly greater than 50% of the flowmeter's full-scale scale.

Reference flow range

Caliber (mm)	Flow range (m3/h)	Caliber (mm)	Flow range (m3/h)
φ15	0.06~6.36	φ450	57.23～5722.65
φ20	0.11～11.3	φ500	70.65～7065.00
φ25	0.18～17.66	φ600	101.74～10173.6
φ40	0.45～45.22	φ700	138.47～13847.4
φ50	0.71～70.65	φ800	180.86～18086.4
φ65	1.19～119.4	φ900	?228.91～22890.6
φ80	1.81～180.86	φ1000	?406.94～40694.4
φ100	2.83～282.60	φ1200	553.90～55389.6
φ150	6.36～635.85	φ1600	723.46～72345.6
φ200	11.3～1130.4	φ1800	915.62～91562.4
φ250	17.66～176.25.	φ2000	1130.4～113040.00
φ300	25.43～2543.40	φ2200	1367.78～136778.4
φ350	34.62～3461.85	φ2400	1627.78～162777.6
φ400	45.22～4521.6	φ2600	1910.38～191037.6

Type spectrum

model	caliber
LDE	15~2600
		code name	electrode material
		K1	316L
		K2	HB
		K3	HC
		K4	titanium
		K5	Tantalum
		K6	Platinum alloy
		K7	Stainless steel coated with tungsten carbide
			code name	Lining material
			C1	Polytetrafluoroethylene F4
			C2	Perfluoroethylene propylene F46
			C3	Polyfluoroethylene FS
			C4	Polyvinyl rubber
			C5	Polyurethane rubber
				code name	function
				E1	Level 0.3
				E2	Level 0.5
				E3	Level 1
				F1	4－20Madc, Load ≤ 750 Ω
				F2	0-3kHz, 5V active, variable pulse width, output high-end effective frequency
				F3	RS485 interface
				T1	Room temperature type
				T2	high-temperature type
				T3	Ultra high temperature type
				P1	1．0MPa
				P2	1．6MPa
				P3	4．0MPa
				P4	16MPa
				D1	220VAC±10％
				D2	24VDC±10％
				J1	Integrated structure
				J2	Split type structure
				J3	Explosion proof integrated structure